 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| 1. general description the 74lvc126a consists of four non-inverting buffers/line drivers with 3-state outputs, which are controlled by the output enable in put (noe). a low at noe causes the outputs to assume a high-impedance off-state. it is a high-performance, low-power, low-volt age, si-gate cmos device, superior to most advanced cmos comp atible ttl families. inputs can be driven from either 3.3 v or 5 v de vices. when disabled, up to 5.5 v can be applied to the outputs. 2. features ? 5 v tolerant inputs/outputs for interfacing with 5 v logic ? wide supply voltage range from 1.2 v to 3.6 v ? cmos low power consumption ? direct interface with ttl levels ? complies with jedec standard jesd8-b / jesd36 ? esd protection: ? hbm jesd22-a114-c exceeds 2000 v ? cdm jesd22-c101-c exceeds 1000 v ? specified from ? 40 c to +85 c and ? 40 c to +125 c 3. ordering information 74lvc126a quad buffer/line driver with 5 v tolerant input/ outputs; 3-state rev. 06.00 ? 16 may 2006 product data sheet table 1: ordering information type number package temperature range name description version 74lvc126ad ? 40 c to +125 c so14 plastic small outl ine package; 14 leads; body width 3.9 mm sot108-1 74lvc126adb ? 40 c to +125 c ssop14 plastic shrink small outline package; 14 leads; body width 5.3 mm sot337-1 74lvc126apw ? 40 c to +125 c tssop14 plastic thin small outline package; 14 leads; body width 4.4 mm sot402-1 74lvc126abq ? 40 c to +125 c dhvqfn14 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 14 terminals; body 2.5 3 0.85 mm sot762-1
74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 2 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state 4. functional diagram 5. pinning information 5.1 pinning fig 1. logic symbol fig 2. iec logic symbol mna235 1a 1y 2 1 3 1oe 2a 2y 5 4 6 2oe 3a 3y 9 10 8 3oe 4a 4y 12 13 11 4oe mna236 1 en1 1 3 2 4 6 5 10 8 9 13 11 12 fig 3. logic diagram mna234 noe na ny (1) * the die substrate is attached to this pad using conductive die attach material. it can not be used as a supply pin or input. fig 4. pin configuration for so14 and (t)ssop14 fig 5. pin configuration for dhvqfn14 126 1oe v cc 1a 4oe 1y 4a 2oe 4y 2a 3oe 2y 3a gnd 3y 001aac982 1 2 3 4 5 6 7 8 10 9 12 11 14 13 001aac98 3 126 transparent top view 2y 3a 2a 3oe 2oe 4y 1y 4a 1a 4oe gnd 3y 1oe v cc 6 9 5 10 4 11 3 12 2 13 7 8 1 14 terminal 1 index area gnd (1) 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 3 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state 5.2 pin description 6. functional description [1] h = high voltage level l = low voltage level x = don?t care z = high impedance off-state. table 2: pin description symbol pin description 1oe 1 data enable input (active high) 1a 2 data input 1y 3 data output 2oe 4 data enable input (active high) 2a 5 data input 2y 6 data output gnd 7 ground (0 v) 3y 8 data output 3a 9 data input 3oe 10 data enable input (active high) 4y 11 data output 4a 12 data input 4oe 13 data enable input (active high) v cc 14 supply voltage table 3: functional table [1] inputs outputs noe na ny hl l hhh lxz 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 4 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state 7. limiting values [1] the input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] for so14 packages: above 70 c the value of p tot derates linearly with 8 mw/k. for (t)ssop14 packages: above 60 c the value of p tot derates linearly with 5.5 mw/k. for dhvqfn14 packages: above 60 c the value of p tot derates linearly with 4.5 mw/k. 8. recommended operating conditions table 4: limiting values in accordance with the absolute ma ximum rating system (iec 60134). symbol parameter conditions min max unit v cc supply voltage ? 0.5 +6.5 v i ik input clamping current v i < 0 v - ? 50 ma v i input voltage [1] ? 0.5 +6.5 v i ok output clamping current v o > v cc or v o < 0 v - 50 ma v o output voltage output high or low-state [1] ? 0.5 v cc + 0.5 v output 3-state [1] ? 0.5 +6.5 v i o output current v o = 0 to v cc - 50 ma i cc supply current - + 100 ma i gnd ground current - ? 100 ma t stg storage temperature [2] ? 65 +150 c p tot total power dissipation t amb = ? 40 c to +125 c-500mw table 5: recommended operating conditions symbol parameter conditions min typ max unit v cc supply voltage 1.2 - 3.6 v v i input voltage 0 - 5.5 v v o output voltage output high or low state 0 - v cc v output 3-state 0 - 5.5 v t amb ambient temperature in free air ? 40 - +125 c ? t/ ? v input transition rise and fall rate v cc = 1.65 v to 2.7 v 0 - 20 ns/v v cc = 2.7 v to 3.6 v 0 - 10 ns/v 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 5 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state 9. static characteristics table 6: static characteristics at recommended operating conditions. volt ages are referenced to gnd (ground = 0 v). symbol parameter conditions min typ [1] max unit t amb = ? 40 c to +85 c v ih high-level input voltage v cc = 1.2 v 1.08 - - v v cc = 1.65 v to 1.95 v 0.65 v cc -- v v cc = 2.3 v to 2.7 v 1.7 - - v v cc = 2.7 v to 3.6 v 2.0 - - v v il low-level input voltage v cc = 1.2 v - - 0.12 v v cc = 1.65 v to 1.95 v - - 0.35 v cc v v cc = 2.3 v to 2.7 v - - 0.7 v v cc = 2.7 v to 3.6 v - - 0.8 v v oh high-level output voltage v i =v ih or v il i o = ? 100 a; v cc = 1.65 v to 3.6 v v cc ? 0.2 - - v i o = ? 4ma; v cc = 1.65 v v cc ? 0.45 - - v i o = ? 8ma; v cc = 2.3 v v cc ? 0.5 - - v i o = ? 12 ma; v cc = 2.7 v v cc ? 0.5 - - v i o = ? 18 ma; v cc = 3.0 v v cc ? 0.6 - - v i o = ? 24 ma; v cc = 3.0 v v cc ? 0.8 - - v v ol low-level output voltage v i =v ih or v il i o =100 a; v cc = 1.65 v to 3.6 v - - 0.2 v i o =4ma; v cc = 1.65 v - - 0.45 v i o =8ma; v cc = 2.3 v - - 0.6 v i o =12ma; v cc = 2.7 v - - 0.4 v i o =24ma; v cc = 3.0 v - - 0.55 v i i input leakage current v cc = 3.6 v; v i =5.5vorgnd - 0.1 5 a i oz off-state output current v i =v ih or v il ; v cc = 3.6 v; v o = 5.5 v or gnd; [2] - 0.1 5 a i off power-off leakage supply v cc = 0 v; v i or v o = 5.5 v - 0.1 10 a i cc supply current v cc = 3.6 v; v i =v cc or gnd; i o =0 -0.110 a ? i cc additional supply current per input pin v cc = 2.7 v to 3.6 v; v i = v cc ? 0.6 v; i o =0 - 5 500 a c i input capacitance v cc = 0 v to 3.6 v; v i = gnd to v cc -4.0-pf t amb = ? 40 c to +125 c v ih high-level input voltage v cc = 1.2 v 1.08 - - v v cc = 1.65 v to 1.95 v 0.65 v cc -- v v cc = 2.3 v to 2.7 v 1.7 - - v v cc = 2.7 v to 3.6 v 2.0 - - v v il low-level input voltage v cc = 1.2 v - - 0.12 v v cc = 1.65 v to 1.95 v - - 0.35 v cc v v cc = 2.3 v to 2.7 v - - 0.7 v v cc = 2.7 v to 3.6 v - - 0.8 v 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 6 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state [1] all typical values are measured at v cc = 3.3 v (unless stated otherwise) and t amb =25 c. [2] for i/o ports, the parameter i oz includes the input leakage current. 10. dynamic characteristics v oh high-level output voltage v i =v ih or v il i o = ? 100 a; v cc = 1.65 v to 3.6 v v cc ? 0.3 - - v i o = ? 4ma; v cc = 1.65 v v cc ? 0.6 - - v i o = ? 8ma; v cc = 2.3 v v cc ? 0.65 - - v i o = ? 12 ma; v cc = 2.7 v v cc ? 0.65 - - v i o = ? 18 ma; v cc = 3.0 v v cc ? 0.75 - - v i o = ? 24 ma; v cc = 3.0 v v cc ? 1- - v v ol low-level output voltage v i =v ih or v il i o =100 a; v cc = 1.65 v to 3.6 v - - 0.3 v i o =4ma; v cc = 1.65 v - - 0.65 v i o =8ma; v cc = 2.3 v - - 0.8 v i o =12ma; v cc = 2.7 v - - 0.6 v i o =24ma; v cc = 3.0 v - - 0.8 v i i input leakage current v cc = 3.6 v; v i =5.5vorgnd - - 20 a i oz off-state output current v i =v ih or v il ; v cc = 3.6 v; v o = 5.5 v or gnd; [2] -- 20 a i off power-off leakage supply v cc = 0.0 v; v i or v o = 5.5 v - - 20 a i cc supply current v cc = 3.6 v; v i =v cc or gnd; i o =0 --40 a ? i cc additional supply current per input pin v cc = 2.7 v to 3.6 v; v i = v cc ? 0.6 v; i o =0 --5000 a table 6: static characteristics ?continued at recommended operating conditions. volt ages are referenced to gnd (ground = 0 v). symbol parameter conditions min typ [1] max unit table 7: dynamic characteristics voltages are referenced to gnd (ground = 0 v). for test circuit see figure 8 . symbol parameter conditions min typ [1] max unit t amb = ? 40 c to +85 c t phl , t plh high to low, low to high propagation delay na to ny see figure 6 v cc = 1.2 v - 11.0 - ns v cc = 1.65 v to 1.95 v 1.2 5.2 10.2 ns v cc = 2.3 v to 2.7 v 0.8 2.8 5.3 ns v cc = 2.7 v 1.5 2.7 4.8 ns v cc = 3.0 v to 3.6 v 1.1 2.4 4.5 ns t pzh , t pzl off-state to high, off-state to low propagation delay noe to ny see figure 7 v cc = 1.2 v - 15.0 - ns v cc = 1.65 v to 1.95 v 2.2 6.7 11.9 ns v cc = 2.3 v to 2.7 v 1.8 3.8 6.6 ns v cc = 2.7 v 1.6 3.1 5.7 ns v cc = 3.0 v to 3.6 v 1.5 3.1 5.3 ns 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 7 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state [1] typical values are measured at t amb =25 c and v cc = 1.8 v, 2.5 v, 2.7 v, and 3.3 v respectively. [2] skew between any two outputs of the same package switching in the same direction. this parameter is guaranteed by design. [3] c pd is used to determine the dynamic power dissipation (p d in w). p d =c pd v cc 2 f i n+ (c l v cc 2 f o ) where: f i = input frequency in mhz, f o = output frequency in mhz, c l = output load capacitance in pf, v cc = supply voltage in volts, n = number of inputs switching, t phz , t plz high to off-state, low to off-state propagation delay noe to ny see figure 7 v cc = 1.2 v - 8.0 - ns v cc = 1.65 v to 1.95 v 1.1 3.3 7.6 ns v cc = 2.3 v to 2.7 v 0.5 1.8 4.3 ns v cc = 2.7 v 2.3 3.4 5.0 ns v cc = 3.0 v to 3.6 v 1.4 2.5 4.6 ns t sk(o) output skew time v cc = 3.0 v to 3.6 v [2] --1.0ns t amb = ? 40 c to +125 c t phl , t plh high to low, low to high propagation delay na to ny see figure 6 v cc = 1.2 v - - - ns v cc = 1.65 v to 1.95 v 1.2 - 13.0 ns v cc = 2.3 v to 2.7 v 0.8 - 7.0 ns v cc = 2.7 v 1.5 - 6.0 ns v cc = 3.0 v to 3.6 v 1.1 - 6.0 ns t pzh , t pzl off-state to high, off-state to low propagation delay noe to ny see figure 7 v cc = 1.2 v - - - ns v cc = 1.65 v to 1.95 v 2.2 - 15.0 ns v cc = 2.3 v to 2.7 v 1.8 - 8.5 ns v cc = 2.7 v 1.6 - 7.0 ns v cc = 3.0 v to 3.6 v 1.5 - 7.0 ns t phz , t plz high to off-state, low to off-state propagation delay noe to ny see figure 7 v cc = 1.2 v - - - ns v cc = 1.65 v to 1.95 v 1.1 - 9.5 ns v cc = 2.3 v to 2.7 v 0.5 - 5.5 ns v cc = 2.7 v 2.3 - 6.5 ns v cc = 3.0 v to 3.6 v 1.4 - 6.0 ns t sk(o) output skew time v cc = 3.0 v to 3.6 v [2] --1.5ns t amb = 25 c c pd power dissipation capacitance per gate. v i = gnd to v cc [3] v cc = 1.65 v to 1.95 v - 6.0 - pf v cc = 2.3 v to 2.7 v - 9.0 - pf v cc = 3.0 v to 3.6 v - 12 - pf table 7: dynamic characteristics ?continued voltages are referenced to gnd (ground = 0 v). for test circuit see figure 8 . symbol parameter conditions min typ [1] max unit 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 8 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state (c l v cc 2 f o ) = sum of the outputs. 11. ac waveforms v m =1.5vatv cc 2.7 v; v m =0.5 v cc at v cc <2.7v; v ol and v oh are typical output voltage drops that occur with the output load. fig 6. the input na to output ny propagation delays mna237 t phl t plh v m v m na input ny output gnd v i v oh v ol measurement points are given in ta b l e 8 . v ol and v oh are typical output voltage drops that occur with the output load. fig 7. 3-state enable and disable times mna684 t plz t phz outputs disabled outputs enabled v y v x outputs enabled output low-to-off off-to-low output high-to-off off-to-high noe input v i v cc v m v ol v oh gnd gnd t pzl t pzh v m v m table 8. measurement points supply voltage input output v cc v m v m v x v y v cc <2.7v 0.5 v cc 0.5 v cc v ol + 0.15 v v oh ? 0.15 v v cc 2.7 v 1.5 v 1.5 v v ol + 0.3 v v oh ? 0.3 v 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 9 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state test data is given in table 9 . definitions for test circuit: r l = load resistance. c l = load capacitance including jig and probe capacitance. r t = termination resistance should be equal to output impedance z o of the pulse generator. v ext = external voltage for measuring switching times. fig 8. load circuitry for switching times v m v m t w t w 10 % 90 % 0 v v i v i negative pulse positive pulse 0 v v m v m 90 % 10 % t f t r t r t f 001aae331 v ext v cc v i v o dut c l r t r l r l pulse generator table 9: test data supply voltage input load v ext v i t r , t f c l r l t plh , t phl t plz , t pzl t phz , t pzh 1.65 v to 1.95 v v cc 2 ns 30 pf 1 k ? open 2 v cc gnd 2.3 v to 2.7 v v cc 2 ns 30 pf 500 ? open 2 v cc gnd 2.7v 2.7v 2.5 ns 50 pf 500 ? open 6 v gnd 3.0vto3.6v 2.7v 2.5 ns 50 pf 500 ? open 6 v gnd 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 10 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state 12. package outline fig 9. package outline sot108-1 (so14) unit a max. a 1 a 2 a 3 b p cd (1) e (1) (1) eh e ll p qz y w v references outline version european projection issue date iec jedec jeita mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 8.75 8.55 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 0 o o 0.25 0.1 dimensions (inch dimensions are derived from the original mm dimensions) note 1. plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 sot108-1 x w m a a 1 a 2 b p d h e l p q detail x e z e c l v m a (a ) 3 a 7 8 1 14 y 076e06 ms-012 pin 1 index 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.35 0.34 0.16 0.15 0.05 1.05 0.041 0.244 0.228 0.028 0.024 0.028 0.012 0.01 0.25 0.01 0.004 0.039 0.016 99-12-27 03-02-19 0 2.5 5 mm scale so14: plastic small outline package; 14 leads; body width 3.9 mm sot108-1 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 11 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state fig 10. package outline sot337-1 (ssop14) unit a 1 a 2 a 3 b p cd (1) e (1) eh e ll p qz y w v references outline version european projection issue date iec jedec jeita mm 0.21 0.05 1.80 1.65 0.25 0.38 0.25 0.20 0.09 6.4 6.0 5.4 5.2 0.65 1.25 0.2 7.9 7.6 1.03 0.63 0.9 0.7 1.4 0.9 8 0 o o 0.13 0.1 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.25 mm maximum per side are not included. sot337-1 99-12-27 03-02-19 (1) w m b p d h e e z e c v m a x a y 1 7 14 8 a a 1 a 2 l p q detail x l (a ) 3 mo-150 pin 1 index 0 2.5 5 mm scale ssop14: plastic shrink small outline package; 14 leads; body width 5.3 mm sot337-1 a max. 2 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 12 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state fig 11. package outline sot402-1 (tssop14) unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz y w v references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.72 0.38 8 0 o o 0.13 0.1 0.2 1 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot402-1 mo-153 99-12-27 03-02-18 w m b p d z e 0.25 17 14 8 a a 1 a 2 l p q detail x l (a ) 3 h e e c v m a x a y 0 2.5 5 mm scale tssop14: plastic thin shrink small outline package; 14 leads; body width 4.4 mm sot402-1 a max. 1.1 pin 1 index 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 13 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state fig 12. package outline sot762-1 (dhvqfn14) terminal 1 index area 0.5 1 a 1 e h b unit y e 0.2 c references outline version european projection issue date iec jedec jeita mm 3.1 2.9 d h 1.65 1.35 y 1 2.6 2.4 1.15 0.85 e 1 2 0.30 0.18 0.05 0.00 0.05 0.1 dimensions (mm are the original dimensions) sot762-1 mo-241 - - - - - - 0.5 0.3 l 0.1 v 0.05 w 0 2.5 5 mm scale sot762-1 dhvqfn14: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 14 terminals; body 2.5 x 3 x 0.85 mm a (1) max. a a 1 c detail x y y 1 c e l e h d h e e 1 b 26 13 9 8 7 1 14 x d e c b a 02-10-17 03-01-27 terminal 1 index area a c c b v m w m e (1) note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. d (1) 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 14 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state 13. abbreviations 14. revision history table 10. abbreviations acronym description cdm charged device model cmos complementary metal oxide semiconductor dut device under test esd electrostatic discharge hbm human body model ttl transistor transistor logic table 11. revision history document id release date data sheet status change notice supersedes 74lvc126a_6 74lvc126a_6 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 06.00 ? 16 may 2006 15 of 16 philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state 15. legal information 15.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.semiconductors.philips.com. 15.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. philips semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request via the local philips semiconductors sales office. in case of any inconsiste ncy or conflict with the short data sheet, the full data sheet shall prevail. 15.3 disclaimers general ? information in this document is believed to be accurate and reliable. however, philips semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. right to make changes ? philips semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use ? philips semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a philips semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. philips semiconductors accepts no liability for inclusion and/or use of philips semiconductors products in such equipment or applications and therefore such inclusion and/or use is for the customer?s own risk. applications ? applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) may cause permanent damage to the device. limiting values are stress ratings only and and operation of the device at these or any other conditions above those given in the characteristics sections of this document is not implied. exposure to limiting values for extended periods may affect device reliability. terms and conditions of sale ? philips semiconductors products are sold subject to the general terms and condit ions of commercial sale, as published at http://www.semiconductors.philips.com/profile/terms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explic itly otherwise agreed to in writing by philips semiconductors. in case of any inco nsistency or conflict between information in this document and such terms and conditions, the latter will prevail. no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any lic ense under any copyrights, patents or other industrial or intellectual property rights. 15.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 16. contact information for additional information, please visit: http://www.semiconductors.philips.com for sales office addresses, send an email to: sales.addresses@www.semiconductors.philips.com document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this docu ment contains the product specification. philips semiconductors 74lvc126a quad buffer/line driver with 5 v tolerant input/outputs; 3-state ? koninklijke philips electronics n.v. 2006. all rights reserved. for more information, please visit: ht tp://www.semiconductors.philips.com. for sales office addresses, email to: sale s.addresses@www.semiconductors.philips.com. date of release: 16 may 2006 document identifier: 74lvc126a_6 please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 17. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 ordering information . . . . . . . . . . . . . . . . . . . . . 1 4 functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 5 pinning information . . . . . . . . . . . . . . . . . . . . . . 2 5.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 5.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 6 functional description . . . . . . . . . . . . . . . . . . . 3 7 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 recommended operating conditions. . . . . . . . 4 9 static characteristics. . . . . . . . . . . . . . . . . . . . . 5 10 dynamic characteristics . . . . . . . . . . . . . . . . . . 6 11 ac waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . 8 12 package outline . . . . . . . . . . . . . . . . . . . . . . . . 10 13 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 revision history . . . . . . . . . . . . . . . . . . . . . . . . 14 15 legal information. . . . . . . . . . . . . . . . . . . . . . . 15 15.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 15 15.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 15.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 15.4 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 15 16 contact information. . . . . . . . . . . . . . . . . . . . . 15 17 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 |
Price & Availability of 74LVC126APWDG118
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |